![]() At the end, zip tie everything as needed. This way, if my mind changes, I have easy access to the wire.ġ4. Sealed end of LED wires with non-adhesive shrink tubing folded on itself and then covered with adhesive shrink tubing. I chose not to install LED light because they appear purple/blue, and people have had problems with them. Protects wire and tells you to not try that wire again.ġ3. If positap wrong wire, remove positap and then wrap small amount of electric tape. Make sure boards go up when door closes and down when open.ġ2. Positap a wire of correct color and then touch wire coming from computer, if deploys, you have the right wire. Know what wire you are looking for, it does no good selecting the right wire for the driver rear door, but then opening the front door. IMPORTANT: PLACE FUSE IN FIRST, IF NO SPARK, KEEP FUSE IN PLACE AND THEN DISCONNECT AND RECONNECT WIRES TO COMPUTER.ġ0. Before using positaps and selecting wires, make sure everything else is done including having the power connected and the amp in place. If you want to see size of wire, you can pull part of weatherstrip up just at where switch is located. The wire colors are correct for the driver and passenger front and rear door courtesy switches. Silicon sealant should be used on floor grommets when passing wire into interior. Motor assembly goes in the rear door location on both driver and passenger side. Directions are poor, but dont look for videos because they will not follow directions for the model. When putting on black motor housing, don't bother with provided Cinch fasteners, just use small zip ties. Installed AMP research power steps and it was a bit of a struggle, but learned some things in the process. Should fall under own weight without motor.Ħ. Snug but don't tighten bolt for motor and linkage assembly until you have tested with board to make sure spacing is correct between board and car when up and no bind is present. Aside from keeping wires away from hot or moving parts.Run wires just inside inner part of thin rubber wheel well and then OVER frame leading to outside of frame where motor and linkage assembly are.ĥ. This is the point of aluminum mounting brackets.Ĥ. KDSS is compatible, but things are tight. Directions are poor, but don't look for videos because they will not follow directions for the model.Ģ. I'll get some pictures and post them up later or tomorrow.Installed AMP research power steps and it was a bit of a struggle, but learned some things in the process. agreeing to a lift.LOL Then when they're up they look very custom. The ease of entry becomes is a piece of cake, and might well deal the deal maker for the Mrs. I can't tell you what a difference it makes to have these, especially for those of us with challenges getting in like the kids, your short or even pregnant wife, grandma, etc. In fact since it meets the Trail cladding on the wheels, the overall look is very much like it's part of the original design. The step they used in the same one that was originally designed for the Tundra, and it fits perfectly into the side when up. Especially for those of us who've had knee injuries. Moreover going from the step up to sitting down is a very natural and easy movement. Like surfboads, kayak, extra carrier, etc. In addition because the the step comes out away from the vehicle nicely, it makes the perfect platform to stand on while get thing on or off the top. Roughly halfway of the distance as built to get in. I'll measure the exact distance later, but on stock 265/70/17 Nitto Terra Grapplers (which seem to sit a little higher than the OEM tires) the step is only about 8 inches off the ground. The AMP step come down well below and also out away from the side. Made from aluminum, most electric running boards are available in a matte black powder-coat finish with optional stainless steel trim. ![]() Anything can happen when you pop off an OEM (Original Equipment Manufacturer) part. Electric running boards, such as the AMP Research Powerstep, fold down when you need them and retract when not in use. With no disrepect intended for those who got the auto Toyota steps for their rig, I think we're talking apples and oranges. 5th Gen Toyota 4Runner Aftermarket Installs, Step-by-Step and Feild Tests Install When it comes to an aftermarket install, it helps to be prepared. They look very cool and make entry so much easier. My 2013 Trail was used by AMP for the test bed on what will soon be the next addition to their automatic step line. Has anyone done a custom install on this automatic deploying step for the 5th Gen runner?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |